MTU setting

[US.M@JORHAZZARD]

Thanks man have a good day

[swoop101]

And yourself.

[US.M@JORHAZZARD]

just a quickie b4 you disappear back to work how do i set windows scaling to 2 ? the only options DR TCP offers are on off and default ?.

[swoop101]

That I can't answer because that I did not set.

will let you know if I find out.

It looks like it may be automatic when you increase RWIN to over 65535

[US.M@JORHAZZARD]

Again thanks man much appreciated...

---------- Post added at 12:10 ---------- Previous post was at 12:07 ----------

Right then here we go again, i have used your settings and have set MTU in DR TCP to 1500 same as router, i will run tweak test now and post results.

X your figners...

---------- Post added at 12:27 ---------- Previous post was at 12:10 ----------

Are the values in BOLD on the tweak test results page the recommended values that i need to enter into DR tcp ???.

Anyone!!!.

---------- Post added at 13:14 ---------- Previous post was at 12:27 ----------

Ok swoop you Da man thanks for all yr help i think we might have done at last, had to set Rwin to 96360 but it looks ok on the tweak test with the exception of the 2+ second stall detected which looks like that is due to congestion on the network "EVERYBODY GET OFF MY NETWORK" lmAO.

Now the real test to join TS and se how long it takes for me to start going mad again because of vioce breakup and i die a few more times..

Again thanks all for your help especially SWOOP Da man...

will run tweak test in an hour just to see if it was a fluke, ill post...


Thanks again
HAZZ.....

---------- Post added at 13:20 ---------- Previous post was at 13:14 ----------

Ok so it wasn't quite an hour but i couldn't wait but from my original test to this....

1. Your Tweakable Settings:
Receive Window (RWIN): 96360
Window Scaling: 1
Path MTU Discovery: ON
RFC1323 Window Scaling: ON
RFC1323 Time Stamping: OFF
Selective Acks: ON
MSS requested: 1460TTL:131
(less any hops behind firewall)
TTL remaining: 120
TOS/TOS subfield: 0
TOS/Flags:
2. Test 1021081 byte download
Actual data bytes sent: 1025461
Actual data packets: 704
Max packet sent (MTU): 1500
Max packet recd (MTU): 1500
Retransmitted data packets: 3
sacks you sent: 38
pushed data pkts: 108
data transmit time: 6.241 secs
our max idletime: 330.9 ms
transfer rate: 152552 bytes/sec
transfer rate: 1220 kbits/sec
This is not a speed test!
transfer efficiency: 99%
3. ICMP (ping) check
Minimum ping: 88.12 ms
Maximum ping: 133.52 ms
Ping stability:
111.42 107.51 133.52 88.12 88.12 88.62 88.86 88.19 97.89 108.34

Notes and recommendations:
RWIN is in range
Looking good

Notes and recommendations:
Good data stream (no/few rexmits)

Notes and recommendations:
Looking good


I'm a happy bunny again

and yes Swoop you were correct windows scaling is auto set with Rwin above 65535...

[rdhw]

Originally Posted by US.M@JORHAZZARD

Are the values in BOLD on the tweak test results page the recommended values that i need to enter into DR tcp ???.

No, they are the actual values in use detected by the Tweak test. They are not recommendations.

[Jim galbally]

your signal level is sh*t at -12! read the sticky about signal levels.

you can get little devices that go in-line on the coax cable to bring this nearer to 0

[SnoopZ]

Originally Posted by Jim galbally

your signal level is sh*t at -12! read the sticky about signal levels.

you can get little devices that go in-line on the coax cable to bring this nearer to 0

It can still work perfectly well at -12 according to bbking. Mines been -11 and its now -9 and ive never had any problems with speed or drop outs.

[US.M@JORHAZZARD]

So this
Downstream Receive Power Level : -12.5 dBmV is not good then ?

---------- Post added at 22:42 ---------- Previous post was at 21:05 ----------

On dslreports site they used to have a little proggy to calculate your Rwin value, they have since removed it and i was wonderring if anyone had a similar little prog ????....