What have you fixed lately?
02-11-2013, 22:02
|
#61
|
cf.mega poster
Join Date: Mar 2005
Location: Wales
Posts: 2,509
|
Re: What have you fixed lately?
two xbox controllers and a Dell tower running XP ( i had forgotten the joys of the reinstall screens )
|
|
|
04-11-2013, 19:39
|
#62
|
Inactive
Join Date: Oct 2006
Location: Right here!
Posts: 22,316
|
Re: What have you fixed lately?
Fixed the draught-proofing on the openers/vents on 3 of our 5 Velux roof windows. The original 2" wide foam strips stuck on the underside of the wooden openers had perished over the years and took a bit of effort to remove but I managed to replace it with some foil backed thermal insulation and draught excluder to seal and gaps. Made a nice neat job of it even if I say so myself.
|
|
|
19-11-2013, 12:15
|
#63
|
Inactive
Join Date: Oct 2006
Location: Right here!
Posts: 22,316
|
Re: What have you fixed lately?
Well I hope I've just fixed our faulty alarm system.
http://www.cableforum.co.uk/board/35646450-post1.html
Today I thought I'd give it a go so decided to inspect the internal battery. However, as soon as I touched the control panel to unscrew the 4 top cover retaining screws, the tamper went off which shouldn't have happened and was as loud as it was unnerving. After removing the cover, I soon found the tamper switch and could see that one of the 2 small plastic prongs which holds it in place was missing thereby allowing it to rotate. After a lot of looking and some trial and error, I also discovered the black wire from the switch to the circuit board was loose and fell out as soon as I touched it. After reconnecting the wire, I managed to secure the tamper switch into the closed position (as an interim measure) with a cable tie thereby curing the permanent tamper fault and alarm which was doing my head in. I then set about replacing the battery. Sure enough the positive terminal was corroded and stuck in place but after prising it off I was able to clean up the connection and fit the new battery without any problems. I screwed the control panel cover back on and successfully armed/disarmed the system a few times. I'll allow 24 hours for the new battery to charge and then try turning off the mains power supply to see if backup power has been restored. Fingers crossed!....
|
|
|
19-11-2013, 13:34
|
#64
|
Inactive
Join Date: Oct 2006
Location: Right here!
Posts: 22,316
|
Re: What have you fixed lately?
Not sure if you're describing the same thing but one trick I've used before when I'm trying to remove a security screw is to find a slightly smaller bit which fits inside the head of the screw and then wedge something else in between the bit and the inside edges of the head so that when the bit turns the screw head will. I have some heat activated plastic which does the trick nicely, just press some around the loose bit, let it go hard then turn away.
|
|
|
19-11-2013, 14:25
|
#65
|
Inactive
Join Date: Oct 2006
Location: Right here!
Posts: 22,316
|
Re: What have you fixed lately?
Quote:
Originally Posted by heero_yuy
Yes, there's often a way to wedge something in if you don't have the exact bit to hand. There's always a drill for the worst ones and a mole wrench for the stump once apart.
|
Yes, I've also been known to saw a slot in the top of a damaged screw but that's obviously not easy in confined spaces. I've got a set of superwrenches which make easy work of removing broken studs, rounded off nuts and the like plus one of those sonic multi-tools which are great for cutting, sanding and grinding in tight places where there's little room to move and/or you don't want to damage anything else or create loads of dust.
Highly recommended and pay for themselves in just a couple of jobs.
http://www.idealworld.tv/4+Piece+Sup...et-710551.aspx
Bought my set at £19.99 and I'm sure the price will come down again.
http://www.amazon.co.uk/CEL-Multi2PR...ords=cel+tools
Got mine with a couple of sets of the attachments which really are very good quality.
|
|
|
19-11-2013, 14:37
|
#66
|
as common as muck
Join Date: Apr 2009
Location: Dirty Old Town
Posts: 3,515
|
Re: What have you fixed lately?
An old pc that was blue screening, even in safe mode. So I booted from cd using mini xp, then used the chkdsk command which found and fixed a couple of corrupted system files, problem solved.
__________________
I'm not afraid of dying, I just don't want to be there when it happens. -Woody Allen
|
|
|
19-11-2013, 14:39
|
#67
|
Inactive
Join Date: Nov 2010
Location: Surrey
Services: Virgin Cable TV (Tivo) and Freeview
Posts: 1,227
|
Re: What have you fixed lately?
I have fixed myself a cup of tea... sorry if this old gag has been used before....
|
|
|
19-11-2013, 16:32
|
#68
|
Inactive
Join Date: Oct 2006
Location: Right here!
Posts: 22,316
|
Re: What have you fixed lately?
Quote:
Originally Posted by Jimmy-J
An old pc that was blue screening, even in safe mode. So I booted from cd using mini xp, then used the chkdsk command which found and fixed a couple of corrupted system files, problem solved.
|
Like that. Usable PC saved.
|
|
|
19-11-2013, 16:51
|
#69
|
Inactive
Join Date: Jul 2013
Location: Hartlepool
Age: 35
Services: Sky+HD sports and movies HD, sky fibre pro, ps4 and xbox one.
Posts: 478
|
Re: What have you fixed lately?
A outside Christmas light, I was installing it and accidentally twated it with a hammer and knackered it, fixed now though.
|
|
|
20-11-2013, 08:14
|
#70
|
as common as muck
Join Date: Apr 2009
Location: Dirty Old Town
Posts: 3,515
|
Re: What have you fixed lately?
Quote:
Originally Posted by martin201002
A outside Christmas light, I was installing it and accidentally twated it with a hammer and knackered it, fixed now though.
|
lol !
__________________
I'm not afraid of dying, I just don't want to be there when it happens. -Woody Allen
|
|
|
20-11-2013, 16:01
|
#71
|
Inactive
Join Date: Oct 2006
Location: Right here!
Posts: 22,316
|
Re: What have you fixed lately?
Quote:
Originally Posted by Osem
Well I hope I've just fixed our faulty alarm system.
http://www.cableforum.co.uk/board/35646450-post1.html
Today I thought I'd give it a go so decided to inspect the internal battery. However, as soon as I touched the control panel to unscrew the 4 top cover retaining screws, the tamper went off which shouldn't have happened and was as loud as it was unnerving. After removing the cover, I soon found the tamper switch and could see that one of the 2 small plastic prongs which holds it in place was missing thereby allowing it to rotate. After a lot of looking and some trial and error, I also discovered the black wire from the switch to the circuit board was loose and fell out as soon as I touched it. After reconnecting the wire, I managed to secure the tamper switch into the closed position (as an interim measure) with a cable tie thereby curing the permanent tamper fault and alarm which was doing my head in. I then set about replacing the battery. Sure enough the positive terminal was corroded and stuck in place but after prising it off I was able to clean up the connection and fit the new battery without any problems. I screwed the control panel cover back on and successfully armed/disarmed the system a few times. I'll allow 24 hours for the new battery to charge and then try turning off the mains power supply to see if backup power has been restored. Fingers crossed!....
|
Just tested the system by disconnecting the mains supply and the battery backup appears to be working properly so I claim an official 'fix'. Phew!
|
|
|
23-11-2013, 19:01
|
#72
|
cf.mega poster
Join Date: Jun 2006
Location: Sutton-in-Ashfield
Age: 54
Services: Freeview HD
Posts: 1,659
|
Re: What have you fixed lately?
I fixed my old 22" widescreen monitor that wouldn't wake up from sleep mode
Just had to swap a couple of bulging capacitors on the power supply. Wish I'd done that befoer buying a new 27" monitor though.
__________________
I've got 2 GCSE's. 1 in Biology and 1 in Metalwork...If you want your cat welding then I'm your man.
|
|
|
23-11-2013, 20:31
|
#73
|
Inactive
Join Date: Oct 2006
Location: Right here!
Posts: 22,316
|
Re: What have you fixed lately?
Quote:
Originally Posted by heero_yuy
Cupboard door Euro-hinge in the kitchen's been clunking badly when opening. It's the built in self closer that's failed. Fortunately when I put the kitchen in there were a few extra ones that weren't needed so a 5 minute job to fit a replacement. The bit on the carcase stays.
Voila! No clunks.
|
Thanks for that mate! One of mine's been doing the same thing and you just reminded me that I have some spares left over from our kitchen installation somewhere. I'll view this as total vindication of my 'never throw anything away' policy towards DIY stuff.
|
|
|
25-11-2013, 13:41
|
#74
|
laeva recumbens anguis
Cable Forum Team
Join Date: Jun 2006
Age: 67
Services: Premiere Collection
Posts: 42,234
|
Re: What have you fixed lately?
It's called a 'man drawer*'
*Michael McIntyre
__________________
There is always light.
If only we’re brave enough to see it.
If only we’re brave enough to be it.
If my post is in bold and this colour, it's a Moderator Request.
|
|
|
25-11-2013, 22:09
|
#75
|
Inactive
Join Date: Oct 2006
Location: Right here!
Posts: 22,316
|
Re: What have you fixed lately?
Quote:
Originally Posted by Hugh
It's called a 'man drawer*'
*Michael McIntyre
|
In my case it's called a double garage...
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT +1. The time now is 11:52.
|