Possible Bug in VMNG300 firmware?

[pip08456]

Originally Posted by Chrysalis

ok I finished playing.

Was harder to do and I also failed.

On the vmng300 if removing the cable it seems it eithers works with normal power levels or doesnt work, I couldnt get it to be partially connected at reduced power levels. The numerous recconections were all on the same channel.

When I tried on the superhub because of bridge mode I had the same problem I had with the vmng300 in that I couldnt keep refreshing the page to check the channel status as I had to keep doing dhcp renew's on the router to keep been able to connect to the GUI, the superhub had an additional problem because of this I couldnt relogin after a dhcp renew due to a ghosted session and the superhub restriction of one login at a time. Nevertherless I did about 10 attempts and all same channel.

So I am stuck with this jitter now until VM do another upgrade.

Pinging 194.168.4.100 with 32 bytes of data:
Reply from 194.168.4.100: bytes=32 time=11ms TTL=252
Reply from 194.168.4.100: bytes=32 time=9ms TTL=252
Reply from 194.168.4.100: bytes=32 time=22ms TTL=252
Reply from 194.168.4.100: bytes=32 time=25ms TTL=252
Reply from 194.168.4.100: bytes=32 time=12ms TTL=252
Reply from 194.168.4.100: bytes=32 time=11ms TTL=252
Reply from 194.168.4.100: bytes=32 time=9ms TTL=252
Reply from 194.168.4.100: bytes=32 time=8ms TTL=252
Reply from 194.168.4.100: bytes=32 time=11ms TTL=252
Reply from 194.168.4.100: bytes=32 time=21ms TTL=252

Ping statistics for 194.168.4.100:
Packets: Sent = 10, Received = 10, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 8ms, Maximum = 25ms, Average = 13ms

It was only 2-3 weeks or so back when ignition signed up and I posted on his thread I had much better then that to the same ip.

Told you it wouldn't work!

[craigj2k12]

Originally Posted by pip08456

Told you it wouldn't work!

your sometimes right

[pip08456]

Originally Posted by craigj2k11

your sometimes right

Most times but don't always put it over well.

[craigj2k12]

Originally Posted by pip08456

Most times but don't always put it over well.

thats where i come in handy

[pip08456]

Yeh bvut you think channels make a difference- they don't!

[craigj2k12]

Originally Posted by pip08456

Yeh bvut you think channels make a difference- they don't!

they do

[pip08456]

Pantomime time!!!

No they don't!!!

He's behind you!!!

[craigj2k12]

Originally Posted by pip08456

Pantomime time!!!

No they don't!!!

He's behind you!!!

enlighten us then.............

[pip08456]

Nopanic!!!!!!!!!!!

[Chrysalis]

hmm there is a 2nd channel, I got one on 3.58mhz and the ID is 4.

The modem d/c by itself and recconected and I was on that channel but it couldnt lock to a downstream so I waited and then it came back online but back on 4.58mhz

I have had about 2 or 3 d/c during the day as well which were not me messing about.

[Skie]

Originally Posted by craigj2k11

the superhub puts them out of order since R25, dont know why, it was reported in the beta firmware thread but they said it didnt matter. However the VMNG300 puts them in order

I have a VMNG300, not a Superhub

[craigj2k12]

Originally Posted by Skie

I have a VMNG300, not a Superhub

doh, either way it doesnt matter

[pip08456]

Originally Posted by Chrysalis

hmm there is a 2nd channel, I got one on 3.58mhz and the ID is 4.

The modem d/c by itself and recconected and I was on that channel but it couldnt lock to a downstream so I waited and then it came back online but back on 4.58mhz

I have had about 2 or 3 d/c during the day as well which were not me messing about.

Sounds like it could be upgrade work happening in you area.

[Chrysalis]

I hope so. It needs it.

speedio slowing down on some tests now.

[craigj2k12]

speedio freezes in firefox, just a warning. had to do mine in IE