Router connection problem
 

I've recently had TiVo and a Superhub installed. I was already on Virgin broadband and have a dlink router.

The white Virgin cable goes into the back of the Superhub, and then there is an Ethernet connection into the back of the dlink.

I can see the dlink network and it says I am connected to it but when I'm on it, I can't connect to any web pages - the blue bar just hangs.

Whilst the virginmedia wireless connection (via the hub) works ok (although the latest is that it seems to be hanging with this as well) it does not seem to have as good a signal. What do I need to do to reconnect to dlink? Thanks.

Re: Router connection problem
 

If using your own router, put the SHUB in modem mode

Re: Router connection problem
 

I tried turning the SH to modem mode (the button turned purple) but dlink appeared to act the same as before. I then reset the SH to return to the original position, as else I had no wifi. Is the best way to return to normal SH mode to go via the SH settings page?

When I returned to the original position (connected via virginmedia) the Internet seemed to work fine initially but then went back to hanging, as if it's somehow connecting out, but is shown as still being connected (as is dlink). Not sure if I could at least get virginmedia fully working by not having the Ethernet going into the dlink?

Re: Router connection problem
 

The SuperHub IP changes when in modem mode. Start using 192.168.100.1 instead of 192.168.0.1 The former will work in both router and modem mode whereas the latter will only work when the SuperHub is in router mode. You can enable and disable or switch modes via the web interface using the IPs above. Theres no need for you to manually hard reset the SuperHub to get back into router mode.

If the SuperHub is doing well for your wifi needs then disconnect the D Link. If you require the D Link then reset the router by releasing any saved connection info it has saved from your previous set up. Also double check the router is set to obtain dynamic WAN. Set up from scratch if you want, use the wizard within D Links web interface accessible via 192.168.0.1 Obviously don't link the D Link to the SuperHub in router mode and access its web interface, the IPs will clash.

Re: Router connection problem
 

As the virginmedia connection does not seem to last for long, and is not showing as strong as dlink I will have another try at getting only dlink connected. Once I get into the dlink settings page is there an easy way to reset the router and release any saved connection? Before doing so should I have put the SH back into modem only mode? Is dynamic WAN an easy setting to check in dlink settings? Thanks.

Re: Router connection problem
 

Silly question but .... you are remembering to power off the superhub each time you change from or to modem mode?

Re: Router connection problem
 

And another silly question, are you plugging the router into socket 1 which is the only one that works in modem mode?

Re: Router connection problem
 

Not silly questions at all - I'm not too up on this.

When I turned the SH to modem mode I did not also power off the SH as I thought by it changing to purple it had all worked ok, but I did subsequently turn the power off.

The Ethernet cable into the SH is in the furthest left socket - I assume that is socket 1.

Having done that I got back into dlink settings (now connected via 3G) and pressed the reboot button on left of screen. It said it would take about 30 seconds but then the pop up came to access a wireless network and first of all I pressed dlink, but it said I couldn't connect. When it popped up again I pressed cancel, and shortly after the wireless bars were showing at top of screen, but it just got to 0 seconds and hung. I did then change back to 3G but the process still didn't seem to complete. Should I get back to dlink settings again and cancel if wireless pop up comes up?

I should say that all the above has involved me trying to connect with an ipad.

Re: Router connection problem
 

It will be the one next where the Virgin cable screws in. I know nothing about the dlink but if you're connecting to it via an ipad you must have got in to see the screen. There will be a screen on the dlink that tells you all the info about the connection to the cable modem (superhub in this case). Here's what it looks like on a Linksys router running dd-wrt


Configuration Type





Connection Type
Automatic Configuration - DHCP








Connection Uptime
8 days, 14:56:21

IP Address
86.**.**.**

Subnet Mask
255.255.252.0

Gateway
86.**.**.1

DNS 1
208.67.222.222

DNS 2
208.67.220.220

DNS 3
8.8.8.8


Remaining Lease Time
1 day 18:35:33

Re: Router connection problem
 

these are just example, log in to your router to make the changes...

connection type will be asked to be set up during the steps, it'll be easy to find dynamic

Re: Router connection problem
 

Thanks for the posts but it seems the problem was that the ethernet cable was in the wrong socket of the SH, and was not closest to the incoming broadband cable. It should've been put in the right slot by the engineer. There's nothing obvious on the box to say it should go in that one?