Cable Forum

Cable Forum (https://www.cableforum.uk/board/index.php)
-   General IT Discussion (https://www.cableforum.uk/board/forumdisplay.php?f=19)
-   -   DVD burner hangs on leadin (https://www.cableforum.uk/board/showthread.php?t=33646874)

dragon 08-03-2009 14:00
DVD burner hangs on leadin
 
I have a samsung r505 laptop I got from argos in the january sales (so fairly new) i've noticed whenever I goto burn a dvd it just hangs on lead-in and never progresses any further, after about 10mins or so it will just give up.

The discs are Verbatim DVD-R disks, unfortantly I don't have any others atm to try :(


I've successfully burnt cd's before using the drive and I know the software works (tryed power2go and imgburn) as I plugged in a USB burner (LG gsa 4163 drive in a usb caddy) and that burns fine.


Onboard drive is a TEAC DV-W28SR, I'm wondering if it's a problem with the drive or just a case of it doesn't like these perticular discs? :confused:

alferret 08-03-2009 14:28
Re: DVD burner hangs on leadin
 
Its possible that the TEAC dont like the disc's with the current firmware, but on searching the TEAC website I couldnt find mention of that specific drive
http://www.teac.co.jp/dspd/product/product.html

Had a quick look on http://club.cdfreaks.com/ and again there is no mention of this drive.

I would try NERO, give that a go and see if it works.

Hom3r 08-03-2009 16:43
Re: DVD burner hangs on leadin
 
Try using this free CD/DVD sw

http://www.pendriveapps.com/infra-re...-burning-tool/

It will run from a USB flash stick

Stuart 08-03-2009 16:49
Re: DVD burner hangs on leadin
 
Quote:
Originally Posted by alferret (Post 34747548)
Its possible that the TEAC dont like the disc's with the current firmware, but on searching the TEAC website I couldnt find mention of that specific drive
http://www.teac.co.jp/dspd/product/product.html
It could be a drive built specifically for Samsung. My old Sony laptop had a Pioneer drive that was built specifically for Sony.

Hom3r 08-03-2009 17:17
Re: DVD burner hangs on leadin
 
try this software

http://dvd.identifier.cdfreaks.com/

dragon 08-03-2009 19:54
Re: DVD burner hangs on leadin
 
Thanks here's what i says

I also searched for firmware but couldn't find any info about the drive on teac's website.

Nor can I actually locate the laptop on the samsung UK site :(

Code:

----------------------------------------------------------------------------
Unique Disc Identifier : [DVD-R:TYG03]
----------------------------------------------------------------------------
Disc & Book Type :      [DVD-R] - [DVD-R]
Manufacturer Name :      [Taiyo Yuden Co. Ltd.]
Manufacturer ID :        [TYG03]
Blank Disc Capacity :    [2,298,496 Sectors = 4.71 GB (4.38 GiB)]
----------------------------------------------------------------------------
** INFO : Drive = TEAC DV-W28S-R - [FW S.0B] - [ATAPI]
** INFO : Write Capabilities = DVD+R DVD+R-DL DVD+RW
** INFO : Write Capabilities = DVD-R DVD-R-DL DVD-RW DVD-RAM
** INFO : Disc = [DVD-R:TYG03]
** INFO : Reference Speed : 1x DVD = 1385 kBps
** INFO : An Writeable Disc Is Recommended For Accurate Results
** INFO : Write Speeds (Supported By This Drive On This Disc) Listed Below
 
** INFO : GET PERFORMANCE Write Speed Descriptor(s)
Descriptor #1 = 11080 kBps ( 8.00x) - [CLV/Non-Pure CAV]
Descriptor #2 =  8310 kBps ( 6.00x) - [CLV/Non-Pure CAV]
Descriptor #3 =  5540 kBps ( 4.00x) - [CLV/Non-Pure CAV]
Descriptor #4 =  2770 kBps ( 2.00x) - [CLV/Non-Pure CAV]
 
** INFO : MODE SENSE Write Speed Descriptor(s) [Legacy Command]
** WARNING : MODE SENSE Is Obsolete And Not Always Properly Supported
Descriptor #1 = 11080 kBps ( 8.00x) - [CLV/Non-Pure CAV]
Descriptor #2 =  8310 kBps ( 6.00x) - [CLV/Non-Pure CAV]
Descriptor #3 =  5540 kBps ( 4.00x) - [CLV/Non-Pure CAV]
Descriptor #4 =  2770 kBps ( 2.00x) - [CLV/Non-Pure CAV]
----------------------------------------------------------------------------
** INFO : Hex Dump Of 'Media Code'-Block Listed Below
** INFO : 4-Byte Header Preceding 'Media Code'-Block Discarded
** INFO : Format 0Eh - Pre-Recorded Information In Lead-In
0000 : 01 40 c1 fd 9e d8 52 00  02 84 0d 11 66 78 90 00  .@....R.....fx..
0010 : 03 54 59 47 30 33 00 00  04 00 00 00 00 00 00 00  .TYG03..........
0020 : 05 a8 82 00 20 00 02 00  06 09 09 15 a9 9a 90 00  .... ...........
0030 : 07 88 80 00 00 00 00 00  08 07 11 0c 10 0b 06 00  ................
0040 : 09 95 07 0d 0b 68 88 00  0a 80 00 00 00 00 10 00  .....h..........
0050 : 0b 08 16 17 96 88 85 00  0c b7 89 33 83 30 33 00  ...........3.03.
0060 : 0d 00 00 d0 00 00 00 00  00 00                    ..........     
 
** INFO : Hex Dump Of 'Control Data Zone'-Block Listed Below
** INFO : 4-Byte Header Preceding 'CDZ'-Block Discarded
** INFO : Format 10h - Physical Format Information Of Control Data Zone
0000 : 25 0f 02 00 00 03 00 00  00 26 12 7f 00 00 00 00  %........&......
----------------------------------------------------------------------------
[ DVD Identifier V5.2.0 - http://DVD.Identifier.CDfreaks.com ]
----------------------------------------------------------------------------

Welshchris 09-03-2009 23:34
Re: DVD burner hangs on leadin
 
i had a similiar problem where my writer would hang on lead in. I have a Pioneer 112D.

Turned out it was software problem. I upgraded version of Nero and that solved my problem.

Gary L 12-03-2009 20:01
Re: DVD burner hangs on leadin
 
http://www.teac.com/data_storage/dvd...-rw/dv-w28s-r/

neilq 31-03-2009 09:58
Re: DVD burner hangs on leadin
 
I seem to have exactly the same problem with the same model laptop. I have contacted Samsung and they advised doing a backup to cd using Samsung Backup (to see if the problem was with windows or hardware). The backup worked fine, however, I cannot burn using Windows Vista.....
any suggestions??


All times are GMT. The time now is 18:49.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
All Posts and Content are © Cable Forum