[Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

I have a NTL Pace set top box. I have been trying to connect a D-Link DI-524 wirless router to it with out any luck. I just cannont get the WAN light on the router to light. Following instructions to power off set top box, power up router power up set top box then plug items togeather using cat5 cable WAN light on router should light... Well it does not i have even taken the router to the back of the set top box and used a 1m cat5 cable, taken out the crossover adaptor still no luck. I havent even got to the stage of connecting the computer at the momment. Any ideas PLEASE :confused:

Re: NTL Set top box + D-Link DI-524 Router help needed please..
 

I am using a D-Link 614+ and it seems fine. I run a cable from it to the router and use Dynamic settings and never had any problems. Have you tried doing a start.ntl? in browser.

Re: NTL Set top box + D-Link DI-524 Router help needed please..
 

I presume it works if you plug the computer direct, i.e. without the router?

Re: NTL Set top box + D-Link DI-524 Router help needed please..
 

At the moment the pc is connected to the set top box via ethenet cable. This has a cross over adaptor at the set top bob and a usb adaptor so the ethernet cable is connected to the pc via usb.

Re: NTL Set top box + D-Link DI-524 Router help needed please..
 

Try using the cable that currently connects the STB and PC to the router (so it connects the router to the STB).

Re: NTL Set top box + D-Link DI-524 Router help needed please..
 

Have you tried:-
1) Power off computer, router and STB.
2) Connect ethernet cable from router WAN port to STB. (From a quick Google, the WAN port on that router is auto, so should not matter whether you have a cross-over or not).
3) Connect ethernet cable from LAN port on router to computer.
4) Power on STB. Wait for lights to settle.
5) Power on router. Wait for lights to settle.
6) Power on computer.

Re: NTL Set top box + D-Link DI-524 Router help needed please..
 

I will try that. Just seams strange that even before i get to the stage of connecting the computer to the router, powering off STB and Router power on router then STB WAN light will not light yet STB works ok with direct link to PC. Using that now. Allmost seems as though fault with router!!! anyway will try your method tomorrow as need pc at mo many thanks John

Re: NTL Set top box + D-Link DI-524 Router help needed please..
 

John, I have the same problem except I'm using a Terayon cable modem. In addition I cannot upgrade the f/w on the DI-524, current version 1.02. This is the second Di-524 I have tried and both exhibit identical symptoms. Did you manage to solve your problem? Roger

Re: NTL Set top box + D-Link DI-524 Router help needed please..
 

Just bought a D-Link DI-634M and I am also having problems. connected up and rebooted as per Quick Start instructions, all status lights appear OK, although I noticed the wireless LAN light was not steady, it was a constant on/off orange, not a fast blinking. Powered up the PC and opened IE and it opened on the Ntl provisioning page. Was this my first mistake, instead of proceeding with the Ntl provisioning I entered the url instructed in the Quick Start guide and everything seemed to progress normally. Zone alarm Pro popped up a 'New Network' warning which I allowed trusted access to. however I cannot now connect to the internet. I tried to reboot the PC and it was still trying to reboot after 20 minutes, it appears that ZA Pro was trying to initialise. I could not shut down the PC and had to use the reset button, or turn off at the mains. I have for now, unplugged the router and rebooted STB & PC and it is working fine again. I did try to go through the whole routine again to see if I could get to the Ntl provisioning page but the PC would not boot correctly. I tried to check the IP that DCHP had assigned with the router connected, it ended in .0.100, although it reported that the Lan connection was working OK. Not sure if that means anything.:dunce:

Any suggestions.:confused:

Should I have gone through registration?
 

I tried to connect a D-Link 634M today, when I reached the step in the instructions to open my browser it went onto the Ntl provisioning page. Should I have continued with this first? I didn't and cannot get a 'live' connection. See this post.http://www.cableforum.co.uk/board/sh...83&postcount=9

If I reset the router to factory defaults and try again, going through the Ntl provisioning stage first, will it cure my problem?

Re: Should I have gone through registration?
 

provsioning is needed when you connect a device with a different mac address to the set top box.

Shouldn't be any need to reset to factory settings.

Also no need for two thread covering the same issue so i have merged.

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

Sorry about the duplicate thread Chris, but I was overwhelmed by the flood of answers to my first post.:rolleyes: :) :angel:

Still getting nowhere fast.
Reset router to factory defaults and went through the setup procedure again. Connected all the cables in the correct order and booted STB when instructed. All router lights OK.
Booted up the PC, at this point it booted perfectly, as fast as normal. opened IE and was once again presented with the Ntl registration page. This time I entered a name for the router and it was registered and accepted. As instructed by the registration page, I rebooted PC & STB. I then entered the url, 192.168.0.1 as per the router setup instructions and the Setup Wizard opened and all seemed to go OK. It did show my correct MAC address, but I clicked on 'Clone' as instructed. I did not set up any encryption at this point, thinking I could return to that at a later stage.
I then clicked 'Finish' and the screen counted down for a few minutes until it completed the setup. I then closed the Setup window and tried to open IE but got a DNS error message almost at once.
I opened the LAN setttings via the Systay icon and it reported that the connection was OK. The details are as follows.
IP 192.168.0.100
Default Gateway 192.168.0.1
DHCP 192.168.0.1
DNS 192.168.0.1
I switched off the PC and tried to reboot, this took around 15 minutes, with a couple of warnings that ZA Pro was initialising. I also found that I had to switch off the PC at the mains to shut it down.
If I remove the ethernet cable between the router and the PC, the PC will boot correctly, except for a 'cable unplugged' warning. If I replace this cable and remove the cable from the STB to the router the PC bootup stalls. I have tried with ZA Pro shut down without success.

If I remove the router and connect direct to the STB/ network card it works perfectly. The new laptop I am typing this from using my Zen dial up reports that it is receiving a strong signal from the router, but it also will not connect.

Any suggestions gratefully recieved.

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

you don't need to clone the mac address-

when you provisioned the router, this registeredd it's mac address to the ntl network, hence no need to clone the pc's mac, as this would also require provisioning.

If i were you do the following:
- Disconnect and power down STB
- reset router to factory settings
- power up stb
- connect router to stb
- provision router
- reboot stb and router
- Try the wired connection if AOK try the wireless connection.

Sorted :)

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

Well, I have somehow got it working.:confused:

I reset the router to factory defaults, connected and rebooted the STB & PC in the prescribed order. When the PC rebooted I noticed that the Prevx Pro and ZA Pro icons in the systray had both enabled without any hold up. So I opened IE and blow me down, straight to Google without Ntl registration or using the D-Link setup site. :cool:
Thanks Chris, not sure how it cleared, could it be DNS delay ?

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

none, it was that you had already provisioned the stbs mac address...

should have realised that when i replied! glad it is working anyway :tu:

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

And this post is via the new Wi Fi laptop,:D One happy bunny.

---------- Post added at 20:56 ---------- Previous post was at 20:29 ----------

One last question Chris, then I will leave you alone ( for now) ;)

Would you advise setting encryption on. ?

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

Oh yes...!

Unless you fancy providing free internet access to your neighbours or anyone who wanders past your house with a wireless enabled device get the security set up :tu:

WPA is best, but WEP is perfectly adequate.

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

Thanks again Chris, this router supports both so I will get to work on it.

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

It's really easy to do Jim, I got round to setting mine the other night and took me all of two minutes :tu:

Only had the router for two years so god knows who's been getting free access all this time oops:

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

Well there you go, you have been allowing all the locals free access to your 'connections' and I thought that you were a good girl.:D

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

I thought it was to good to last. Working fine last night, came to boot up the PC this morning and once again it froze on boot up. Tried the laptop and it has a perfect wireless connection.:confused:

I think the problem is caused by a couple of programs that 'phone home' on boot up, ZA Pro in particular. If I disconnect the ethernet cable between the PC & router, the PC boots OK, if I then plug the cable back in I have a 'live' connection.
I have had a quick look at ZA Pro settings and have added all the DCHP/DNS/ etc relating to the router to the trusted zone to no avail.
If as I understand the router includes a firewall, is it safe to get rid of Zone Alarm? ( that is easier said than done as well)

May need to have a look at the ZA forums.

Re: NTL Set top box + D-Link DI-524 Router help needed please..
 

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

Just to update this problem. It is a very strange one to be sure. I have now discovered when the fault occurs.
Now that the router is registered with Ntl, if I go through the full router setup procedure it works fine, I can reboot my PC using Start/Turn off computer/Restart without any problem. The freezing on boot up only occurs after the PC has been shut down completely. Have updated the router firmware and am going to check for latest network card drivers. For the moment I can get it to work fine if I remove the router to PC ethernet cable, boot the PC then plug the cable back into the router.

Did notice that the System Event Viewer is showing lots of DCOM errors.

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

tryed the above still no luck think i will bye another router any ideas on a make that will work?

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

I got over my set up problem by configuring the Wiireless Router as an Access Point. Originally I intentended replacing a Wired Belkin Router with the D-Link but ended up using both. The solution works fine and I've ended up with what I set out to achieve, a stable, secure wireless network with good signal strength. Roger.

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

Well, after spending many frustrating hours , I think i have finally sorted it. After asking a question on the ZA forums I was advised to try disabling the 'Load on startup' setting in ZA Pro. I did this and the PC booted perfectly. more or less confirming my suspicions that a conflict between the router and ZA Pro was at the root of my problems. One of the ZA forum guru's was very surprised by this and had never encountered it before.

The strange thing was that even though ZA was not loaded and the PC booted up OK, when I checked Control Panel/Security Center, it reported that ZA Pro was running even though a check via Task Manager showed no sign of the various components of ZA.

I downloaded a fresh copy of ZA Pro, uninstalled the old copy and reinstalled.
The PC is now booting perfectly, all Start up programs including ZA Pro load without a hitch.

ATM the fresh install has all my original program settings in situ but the only things in the Firewall Trusted Zone are 'New Network' & 'Loop back Adapter'

Re: [Merged] NTL Set top box + D-Link DI-524 Router help needed please..
 

Hi Guys,

I am having a similar problem to this wondered if you would take a look cheers

http://www.chetnet.co.uk/portal/foru...ead.php?t=8182


Thankz In Advance
Acestu