![]() |
Not a good idea.....
....to calibrate an oscilloscope I've just gone and bought off ebay with a metal screwdriver :shocked::shocked::shocked:
What a shocking experience :D :D :D :D Still though 10KV really brightens up your day... |
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
Post a picture of your new hairstyle.....:D
|
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
|
Re: Not a good idea.....
|
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
Quote:
hope your ok |
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
It was just a cheap Farnell 12Mhz dualtrace (DVT12-14) I got for £25.. The timebase length was incorrect so just opened it up and synced it into a known good sig gen..
Not had any test equip for years now (apart from a decent multimeter) but want to start doing some new project work (like a 1.09Ghz ADSB reciever) |
Re: Not a good idea.....
I have the Velleman HPS40 and it's useful to have one. my ex boss is looking currently at a Lacroy Waverider 4 input scope, seems like a nice product.
|
Re: Not a good idea.....
Quote:
Calibration....Its not for Girls! Only kidding - I even had to google oscilloscope. |
Re: Not a good idea.....
Quote:
I've had a few 240 volt belt's in my time and came all too close with a 3 phase supply I thought was dead, luckily enough the screw driver tips vaporised in a puff of smoke before I did :shocked: Needless to say the multimeter get's used before I touch anything now. |
Re: Not a good idea.....
I used to stick my fingers in light sockets for a thrill.
|
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
Quote:
Me and my sister used to do it all the time. till our parents caught us doing it. |
Re: Not a good idea.....
Proper calibration is expensive unless you have an accurate standard to match against.
|
Re: Not a good idea.....
Yep, but I don't need the scope for unit measurement instead it's purely for seeing if a signal is there and roughly in the right format :D
I only went in as the timebase sweep was showing as 60% of the screen, might be a dry cap so will give them all a test but at least now it's showing full screen and roughly OK on all the ranges. |
Re: Not a good idea.....
Quote:
I hope your ok. |
Re: Not a good idea.....
OK - so whilst on the subject....what has Kymmy opened up here??!!!....
I was once adjusting the the pots on an old CRT monitor using a plastic tool / screwdriver - all nice and safe...I turned the CRT round to check the picture and - I don't know what possessed me to do it, but I put my hand on the board and the back of the tube. The sensation got to the top of my arm before I wondered what it was and pulled my hand away! Another time - I was plugging in a centronics parallel cable into the back of a Kyocera 1200 printer....after trying to plug it in I remember lying on the floor about 20ft away wondering what had happened - still no idea to this day!! |
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
Quote:
Not the first time I've been shocked and not the last.. And definately not the worst.. That honour goes to half way up a ladder finishing the installation of a CB antenna at my brother's house. I was holding the PL-259 in my mouth whilst taping up some cable and my brother at that point decided to power up a 300W amp.. Not sure which is worse.. EHT or RF burns.. Just glad I managed to not let go of the ladder |
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
Quote:
|
Re: Not a good idea.....
I do have a half finished CDI project in the parts drawers (for replacing the magneto system on a strimmer engine so we can lighten it for a quarter scale model aircraft), dare I get that out and complete it.... It's only 400v on the pre-coil side.. ;)
|
Re: Not a good idea.....
That's what I like to hear. a woman that is good with her hands and doesn't mind getting dirty :D
|
| All times are GMT. The time now is 23:25. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
All Posts and Content are © Cable Forum