Cable Forum

Cable Forum (https://www.cableforum.uk/board/index.php)
-   Science & Technology (https://www.cableforum.uk/board/forumdisplay.php?f=26)
-   -   Not a good idea..... (https://www.cableforum.uk/board/showthread.php?t=33677748)

Gary L 18-05-2011 15:17

Re: Not a good idea.....
 
Quote:

Originally Posted by Mr_love_monkey (Post 35239333)
did you try turning the lights on?

Of course :)

Me and my sister used to do it all the time. till our parents caught us doing it.

Taf 18-05-2011 15:17

Re: Not a good idea.....
 
Proper calibration is expensive unless you have an accurate standard to match against.

Kymmy 18-05-2011 15:36

Re: Not a good idea.....
 
Yep, but I don't need the scope for unit measurement instead it's purely for seeing if a signal is there and roughly in the right format :D

I only went in as the timebase sweep was showing as 60% of the screen, might be a dry cap so will give them all a test but at least now it's showing full screen and roughly OK on all the ranges.

Welshchris 18-05-2011 18:57

Re: Not a good idea.....
 
Quote:

Originally Posted by Kymmy (Post 35238802)
....to calibrate an oscilloscope I've just gone and bought off ebay with a metal screwdriver :shocked::shocked::shocked:

What a shocking experience :D :D :D :D Still though 10KV really brightens up your day...

Kymmy many years ago i was thrown clean across my friends living room by a shock and his room is 2 rooms which have been knocked into one and is almost 30ft long, up one end is his dining room and other is the sitting area and i landed about 1ft short of going through his bay window. I was in such a state he wanted to call an ambulance but i said no way and i wasnt right for days after.

I hope your ok.

LSainsbury 18-05-2011 20:03

Re: Not a good idea.....
 
OK - so whilst on the subject....what has Kymmy opened up here??!!!....

I was once adjusting the the pots on an old CRT monitor using a plastic tool / screwdriver - all nice and safe...I turned the CRT round to check the picture and - I don't know what possessed me to do it, but I put my hand on the board and the back of the tube.

The sensation got to the top of my arm before I wondered what it was and pulled my hand away!

Another time - I was plugging in a centronics parallel cable into the back of a Kyocera 1200 printer....after trying to plug it in I remember lying on the floor about 20ft away wondering what had happened - still no idea to this day!!

AntiSilence 18-05-2011 20:06

Re: Not a good idea.....
 
Quote:

Originally Posted by CycoSymz (Post 35238901)
I hate it when that happens:shocked:

Yes... Insulated trimmer tool, anyone? ;) lol

Mr_love_monkey 18-05-2011 20:36

Re: Not a good idea.....
 
Quote:

Originally Posted by LSainsbury (Post 35239692)
I was plugging in a centronics parallel cable into the back of a Kyocera 1200 printer....after trying to plug it in I remember lying on the floor about 20ft away wondering what had happened - still no idea to this day!!

Aliens! did your backside hurt after?

Peter_ 18-05-2011 20:47

Re: Not a good idea.....
 
Quote:

Originally Posted by Mr_love_monkey (Post 35239740)
Aliens! did your backside hurt after?

You believe that he was probed I take it.:D

Mr_love_monkey 18-05-2011 20:51

Re: Not a good idea.....
 
Quote:

Originally Posted by Masque (Post 35239760)
You believe that he was probed I take it.:D

or wondering where the other end of the cable was plugged into

Kymmy 18-05-2011 20:56

Re: Not a good idea.....
 
Quote:

Originally Posted by AntiSilence (Post 35239698)
Yes... Insulated trimmer tool, anyone? ;) lol

Yep, after it happened I used a piece of heat shrink to coat the screw driver shaft and handle.. Then continued..

Not the first time I've been shocked and not the last.. And definately not the worst.. That honour goes to half way up a ladder finishing the installation of a CB antenna at my brother's house. I was holding the PL-259 in my mouth whilst taping up some cable and my brother at that point decided to power up a 300W amp.. Not sure which is worse.. EHT or RF burns.. Just glad I managed to not let go of the ladder

LSainsbury 18-05-2011 20:59

Re: Not a good idea.....
 
Quote:

Originally Posted by Mr_love_monkey (Post 35239767)
or wondering where the other end of the cable was plugged into

Strangely enough - in the back of IBM PS/2 model 50...

Peter_ 18-05-2011 21:01

Re: Not a good idea.....
 
Quote:

Originally Posted by Kymmy (Post 35239769)
Yep, after it happened I used a piece of heat shrink to coat the screw driver shaft and handle.. Then continued..

Not the first time I've been shocked and not the last.. And definately not the worst.. That honour goes to half way up a ladder finishing the installation of a CB antenna at my brother's house. I was holding the PL-259 in my mouth whilst taping up some cable and my brother at that point decided to power up a 300W amp.. Not sure which is worse.. EHT or RF burns.. Just glad I managed to not let go of the ladder

Did you give him a new new names once you recovered enough of your wits.;)

AntiSilence 19-05-2011 18:59

Re: Not a good idea.....
 
Quote:

Originally Posted by Kymmy (Post 35239769)
Yep, after it happened I used a piece of heat shrink to coat the screw driver shaft and handle.. Then continued..

Not the first time I've been shocked and not the last.. And definately not the worst.. That honour goes to half way up a ladder finishing the installation of a CB antenna at my brother's house. I was holding the PL-259 in my mouth whilst taping up some cable and my brother at that point decided to power up a 300W amp.. Not sure which is worse.. EHT or RF burns.. Just glad I managed to not let go of the ladder

OUCH! I bet you had a few choice words for him!

Kymmy 19-05-2011 19:26

Re: Not a good idea.....
 
I do have a half finished CDI project in the parts drawers (for replacing the magneto system on a strimmer engine so we can lighten it for a quarter scale model aircraft), dare I get that out and complete it.... It's only 400v on the pre-coil side.. ;)

Gary L 19-05-2011 22:25

Re: Not a good idea.....
 
That's what I like to hear. a woman that is good with her hands and doesn't mind getting dirty :D


All times are GMT. The time now is 23:32.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
All Posts and Content are © Cable Forum